Operating instructions WRG 3010 E S. 1

Operating instructions WRG 3010 E - Overview of all pages (1 - 114)

Page1

Page2

Page3

Page4

Page5

Page6

Page7

Page8

Page9

Page10

Page11

Page12

Page13

Page14

Page15

Page16

Page17

Page18

Page19

Page20

Page21

Page22

Page23

Page24

Page25

Page26

Page27

Page28

Page29

Page30

Page31

Page32

Page33

Page34

Page35

Page36

Page37

Page38

Page39

Page40

Page41

Page42

Page43

Page44

Page45

Page46

Page47

Page48

Page49

Page50

Page51

Page52

Page53

Page54

Page55

Page56

Page57

Page58

Page59

Page60

Page61

Page62

Page63

Page64

Page65

Page66

Page67

Page68

Page69

Page70

Page71

Page72

Page73

Page74

Page75

Page76

Page77

Page78

Page79

Page80

Page81

Page82

Page83

Page84

Page85

Page86

Page87

Page88

Page89

Page90

Page91

Page92

Page93

Page94

Page95

Page96

Page97

Page98

Page99

Page100

Page101

Page102

Page103

Page104

Page105

Page106

Page107

Page108

Page109

Page110

Page111

Page112

Page113

Page114

Conventions

Warning signs, symbols and text formatting used in this manual
Explanation of text formatting

Safety instructions

Disclaimer in the event of non-compliance
Requirements for the personnel
Intended Use
Five safety rules according to DGUV Regulation 3
Electrostatic-sensitive components and control components (ESD)

ESD - Rules for handling and working

Abbreviations used

System Design of WRG 3010 E

Connections

Application of WRG 3010 E
Function of WRG 3010 E

High Temperature Heat Recovery HT
Low Temperature Heat Recovery LT
Air conditioning operation
Power Signal
Desuperheating
Pressure boost
Gas cooler fan switch-off
Gas cooler bypass GCBP
Air heat pump LWP
Archiving of operating data
Calibration of the Pt1000 Temperature Sensor
Service Area Analogue Inputs and Outputs
Troubleshooting

Installation and Start-Up of WRG 3010 E

Top-Hat Rail Mounting

Mounting on the DIN Rail
Removal from the DIN Rail
Handling Wide COMBICON Plugs

SIOX Extension Module - for Top-Hat Rail Mounting

Connection of the SIOX modules to the controller

Basic Settings Hardware

Settings via DIP Switch S1
Setting the CAN Bus Address Using Decade Switch S2
Setting of the Interface RS485/TTY Using Jumper J1
Configuration of the Analogue Inputs and Outputs at the Factory
Power Supply

Status LEDs

Quick Commissioning
Battery replacement
Firmware Update

Requirements for firmware update
Update of the current firmware

Pin and Terminal Assignments of WRG 3010 E

Connections for 230 V AC (top)

Terminal Assignment of the 230 V AC Power Supply
Terminal Assignment of the Relay Outputs - 230 V AC
Terminal Assignment of the Digital Inputs - 230 V AC

Connections for Protective Extra-Low Voltage (bottom)

Terminal Assignment of the Analogue Inputs
Terminal Assignment of the Analogue Outputs

Connections for Interfaces (on the side)

Terminal Assignment of CAN Bus
Terminal Assignment of RS232 and TTY
Terminal Assignment of RS485
Terminal Assignment of SIOX

Manual/Automatic Operating Modes
Operation of WRG 3010 E

Integration in LDSWin
Visualisation in LDSWin - WRG 3010 E
Visualisation in LDSWin - HT / LT / Power Signal Setpoints
Visualisation in LDSWin - GCBP / LWP / air conditioning operation setpoints
Visualisation in LDSWin - Service Area

Decommissioning and disposal

Decommissioning / Dismantling
Disposal

Alarms and messages of WRG 3010 E

Message system
Display of the Messages and Alarms in the System Centre

Technical Data WRG 3010 E

Electrical data
Mechanical Data WRG 3010 E

Order numbers and accessories of WRG 3010 E

Controller for heat recovery WRG 3010 E
Accessories for WRG 3010 E

Operating instructions WRG 3010 E - Overview of all pages (1 - 114)

Table of Contents