Registrieren Anmelden

Operating instructions GLT x010 (S. 95/120)

Operating instructions GLT x010 (S. 95/120)

Operating instructions GLT x010 (S. 95/120)

Erste Seite

Vorige Seite

Nächste Seite

Letzte Seite

Übersicht aller Seiten

Vollbildanzeige

Das Dokument wird geladen...

Punktgenauer Marker

Erste Seite

Vorige Seite

Nächste Seite

Letzte Seite

Übersicht aller Seiten

Vollbildanzeige

Inhaltsverzeichnis

Conventions

Warning signs, symbols and text formatting used in this manual
Explanation of text formatting

Safety instructions

Disclaimer in the event of non-compliance
Requirements for the personnel
Intended Use
Five safety rules according to DGUV Regulation 3
Electrostatic-sensitive components and control components (ESD)
EGB - Richtlinien zur Handhabung
Abbreviations Used

System design GLT x010

Connections
GLT x010 models

Number of data points
Synchronisation
Compatibility

Tasks of the GLT x010
Functions of the GLT x010 and set-up

Implementation
Starting Characteristics

First Start
Restart

Controller configuration

Measuring ranges of the Pt1000 sensor inputs
Measuring ranges of the analogue inputs
Measuring ranges of the analogue outputs
Number of SIOX extension modules
System error messages

Process Image (PI)

Feedback of the manual control level
Pt1000 sensor inputs
Analogue inputs
Analogue outputs
System Status

Status of the CAN bus
CAN bus address status
Status of the SIOX 1..3 extension modules
Status of the battery and DIP switches
Status of the Life LED (life lamp)

Signal List

Formal structure of the Signal List
The Column Markers

Marker $EA1 - Address according to IEC 61131-3
Marker $EA2 - Variable identifier
Marker $REF - channel reference
Marker $LDSW, $ARC, $ARCNR - LDSWin visualisation
Marker $FTYP, $FTZ, $FN - Probes and sensors
Marker $YMIN, $YMAX, $SM, $B, $E, $DEF
Marker $PRIO - Alarm priority

Signal List Tool

Starting the tool and settings
Menu functions
Error message examples
Changes of GLT 5010 compared to GLT 3010

CODESYS

Creation of the application using CODESYS

Target system settings

Importing the application using CODESYS

Connection to development PC
Compile project and load into DDC
Create boot project and start application

Installation and start-up GLT x010 / SIOX

DIN rail mounting

Mounting on the DIN rail
Removal from the DIN rail
Handling Wide COMBICON Plugs

SIOX Extension Module

Connection of the SIOX modules to the base module

Default hardware settings

Settings using DIP switch S1
Setting the CAN bus address using decade switch S2
Setting of the interfaces RS485/TTY using jumper J1
Configuration of the analogue inputs and outputs at the factory
Power supply

Status LEDs

Replacing the battery
Firmware Update

Requirements for firmware update
Update der aktuellen Firmware

Connection and terminal assignment GLT x010 / SIOX

Assignment of all inputs and outputs
Connections for 230 V AC (top)

Assignment of the 230 V AC power supply
Assignment of the relay outputs - 230 V AC / 24 V AC/DC
Assignment of the digital inputs - 230 V AC / 24 V AC/DC

Configuration of the digital inputs 230 V AC / 24 V AC/DC

Connections for safety extra-low voltage (bottom)

Assignment of the analogue inputs
Assignment of the analogue outputs

Connections for interfaces (on the side)

CAN Bus Assignment
Assignment RS232 and TTY
Assignment RS485

Assignment Modbus Modules

Assignment SIOX

Manual / Automatic operating modes changeover
Decommissioning and Disposal

Decommissioning / Dismantling
Disposal

Alarms and Messages GLT x010

Message system
Structure of the messages
Message types
Setting the priorities

Technical Data GLT x010 / SIOX

Electrical Data GLT x010 / SIOX
Mechanische Daten GLT x010

Part numbers and accessories GLT x010

LDS1-Gateway Betriebsanleitung - 20.05.2021 10:10 Uhr