FS 3000 Operating instruction - Overview of all pages (1 - 126)
Page1
Page2
Page3
Page4
Page5
Page6
Page7
Page8
Page9
Page10
Page11
Page12
Page13
Page14
Page15
Page16
Page17
Page18
Page19
Page20
Page21
Page22
Page23
Page24
Page25
Page26
Page27
Page28
Page29
Page30
Page31
Page32
Page33
Page34
Page35
Page36
Page37
Page38
Page39
Page40
Page41
Page42
Page43
Page44
Page45
Page46
Page47
Page48
Page49
Page50
Page51
Page52
Page53
Page54
Page55
Page56
Page57
Page58
Page59
Page60
Page61
Page62
Page63
Page64
Page65
Page66
Page67
Page68
Page69
Page70
Page71
Page72
Page73
Page74
Page75
Page76
Page77
Page78
Page79
Page80
Page81
Page82
Page83
Page84
Page85
Page86
Page87
Page88
Page89
Page90
Page91
Page92
Page93
Page94
Page95
Page96
Page97
Page98
Page99
Page100
Page101
Page102
Page103
Page104
Page105
Page106
Page107
Page108
Page109
Page110
Page111
Page112
Page113
Page114
Page115
Page116
Page117
Page118
Page119
Page120
Page121
Page122
Page123
Page124
Page125
Page126
Table of Contents
1 Design of FS 300
1.1 Introduction
2 <sub>3</sub> t<sub>0</sub> t<sub>0</sub> t<sub>0</sub> t<sub>0</sub> t<sub>0</sub> t<sub>0</sub> t ti o<sup>7</sup> a<sup>2</sup> t<sub>0</sub> t p t c t ti o p t<sub>0</sub> t<sub>0</sub> t p n o c FS c p t o ti n n o p n o <sub>1</sub> A F t p p n<sup>0</sup> o <sub>7</sub> t c t a a t t o l o n
2 <sub>3</sub> . . 1<sup>3</sup> p n . t n o <sub>0</sub> .
C C <sub>6</sub><sub>0</sub>
- - 2 L - . . . 1 . 1 3 trol 1 3
3.3 Neutral zone
3.4 Control algorithm
3.5 Compressor control times
3.6 Determination of setpoint
3.6.1 Setpoint determination with low-pressure control
3.6.2 Setpoint determination with brine outlet temperature control
3.6.3 Setpoint determination with brine inlet temperature control
3.7 Capacity-controlled compressors
3.7.1 Capacity-controlled compressors with dual-circuit systems
3.8 Setpoint increase / decrease
3.9 Control of expansion valves/subcooler FS 3000
3.10 Pumpdown
3.11 Ambient data
3.12 Load shedding
3.13 Compressor base load rotation
3.13.1 Base load rotation for single-circuit systems
3.13.2 Base load rotation with dual-circuit systems
3.14 Compressor monitoring
3.14.1 Safety loop
3.14.2 Monitoring of low oil pressure cutout (reciprocating compressors only)
3.14.3 Monitoring of low oil flow cutout (screw compressors only)
3.14.4 Monitoring of motor overload cutout/phase monitor
3.14.5 Monitoring of cylinder head temperature
3.14.6 Monitoring of high pressure
3.14.7 Monitoring of low pressure
3.14.7.1 Monitoring of low pressure with suction pressure control
3.14.7.2 Monitoring of low pressure with brine control
3.15 Dry cooler control/fan control
3.16 Control type
3.16.1 High pressure control
3.16.2 Control of coolant temperature
3.17 Neutral zone
3.18 Control algorithm
3.18.1 Control algorithm with step controller
3.18.2 Control algorithm with continous control
3.18.3 Temperature hold
3.18.3.1 Control of three-way valve
3.18.4 Control algorithm in heat recovery mode
3.19 Setpoint determination
3.19.1 Setpoint determination with high pressure control by step controller
3.19.2 Setpoint calculation for high pressure control
3.19.3 Setpoint determination with coolant control by step controler
3.19.4 Setpoint determination with continous control
3.20 Dry cooler control times with step controller
3.21 Monitoring condenser fan motors
3.22 Pump control
3.22.1 Pump monitoring
3.22.2 Pump base load rotation
3.22.3 Pump parameter setting
3.23 Flow monitor
3.24 Controller start
3.24.1 First start
3.24.2 Restart
3.25 Central defrosting
3.26 Monitoring
3.26.1 Refrigerant monitoring
3.26.2 Brine and coolant temperature monitoring
3.26.3 Monitoring brine or coolant circuit pressure
3.26.4 Monitoring of external alarm
3.27 Disabling of refrigeration points
3.28 Archiving of operating data
3.28.1 Compressor/fan operating hours
3.28.2 Daily run times and starts
3.28.3 Pack activity/utilization
4 Basic Parameter Setting / Startup of FS 3000
4.1 Connection and safety notes
4.2 Installation
4.3 Basic parameter settings on hardware
4.3.1 Basic settings with S1
4.3.2 Basic settings with S2
4.3.3 Basic parameter settings in software
4.4 Replacing the battery
4.5 Installing update software
4.5.1 Installing update software on the PC
4.5.2 Updating current firmware in FS 3000
5 Pin and Terminal Assignments of FS 3000
5.1 Inputs/outputs for basic version: 4 compressor capacity stages, 4 fan stages
5.2 Inputs/outputs for upgrades version: 6 compressors, 8 compressor capacity stages, 8 fan stages
6 Operating Modes of FS 3000
6.1 Manual control mode
6.2 Service mode
7 Operation of FS 3000
7.1 Operation with CI 3000 Store Computer / AL 300 Operator Terminal
7.2 Menus and screens
7.3 Operation / Parameter setting of FS 3000 Pack Controller
Table of Contents
